ASME B18-16.4:2008 pdf download Serrated Hex Flange Locknuts 90,000 psi (Inch Series)
1 sCOPE
This Standard covers the general,dimensional, andmechanical performance requirements for low strengthcarbon steel, case hardened,regular and large serratedflange locknuts (inch series),recognized as AmericanNational Standard.
2 cOMPARISON To lso STANDARDS
There is no inch series ISO standard for these productsat this time.
3TERMINOLOGY
For definitions of terms relating to fasteners orcomponent features used in this Standard, refer toASME B18.12.
REFERENCE STANDARDS
The following is a list of publications referenced inthis Standard.
ASME B1.1,Unified Inch Screw Threads
ASME B1.3,Screw and Thread Gaging Systems forDimensional Acceptability — Inch and Metric ScrewThreads (UN,UNR,UNJ，M, and MJ)
ASME B18.12,Glossary of Terms for MechanicalFasteners
ASME B18.18.2M, Inspection and Quality Assurance forHigh-Volume Machine Assembly Fasteners
ASME Y14.5M,Dimensioning and Tolerancing
Publisher: The American Society Of MechanicalEngineers (ASME)，Three Park Avenue,New York,NY 10016-5990; Order Department: 22 Law Drive,PO.Box 2300,Fairfield, NJ 07007-2300
ASTM F 606，Test Methods for Determining theMechanical Properties of Externally and InternallyThreaded Fasteners,Washers,Direct TensionIndicators, and Rivets
ASTM F 812,Specification for Surface Discontinuitiesof Nuts,Inch Series
ASTM F1941, Electrodeposited Coatings on ThreadedFasteners [Unified Inch Screw Threads (UN/UNR)]ASTM F 2282,Standard Specification for QualityAssurance Requirements for Carbon and Alloy SteelWire,Rods, and Bars for Mechanical Fasteners
ASTM F 2328,Standard Test Method for DeterminingDecarburization and Carburization in Hardened andTempered Threaded Steel Bolts,Screws, and StudsPublisher: ASTM International,100 Barr Harbor Drive,P.O. Box C700,West Conshohocken,PA 19428-2959
5 DIMENSIONS
a) Unless otherwise specified, all dimensions in thisStandard shall be as specified in Tables 1 and 2, andsections 6 through 9.All dimensions in this Standardare in inches and apply before plating or coating isspecified. When a plating or coating is specified, thefinished product dimensions shall be agreed uponbetween the supplier and purchaser.
(b) Symbols specifying geometric characteristics arein accordance with ASME Y14.5M.
6SERRATIONS
The configuration of the serrations shall be at thediscretion of the manufacturer, provided the perform-ance requirements as specified in para.12.2 are met.
7 TOPS OF NUTS
Tops of nuts shall be flat and chamfered. The lengthof chamfer at hex corners shall be from 5% to 15% ofthe basic thread size.The surface may be slightly convexor rounded.
8TRUE POSITION OF HEXAGON TO TAPPED HOLEAt maximum material condition (MMC), the axis ofthe hexagon shall be located at true position with respectto the axis of the thread pitch diameter within a tolerancezone having a diameter equivalent to 4% of the maxi-mum width across flats.
9coUNTERSINK
Tapped hole shall be countersunk on the bearing faceand may be countersunk on the top.The maximumcountersink diameter shall be the thread basic (nominal)major diameter plus 0.030 in. for %/ in. nominal size nutsand smaller, and 1.08 times the basic major diameter for
ASME B18-16.4:2008 pdf download
