ASME A112.18.1:2005 pdf download

ASME A112.18.1:2005 pdf download Plumbing supply fittings
1.1
This Standard applies to plumbing supply fittings and accessories located between the supply line stop nd the terminal fitting, inclusive, as follows:
(a) automatic compensating valves for individual wall-mounted showering systems;
(b) bath and shower supply fittings;
(c) bidet supply fittings;
(d) clothes washer supply fittings;
(e) drinking fountain supply fittings;
(f) humidifier supply stops;
(g) kitchen, sink, and lavatory supply fittings;
(h) laundry tub supply fittings;
(i) lawn and sediment faucets;
(j) metering and self-closing supply fittings; and
(k) supply stops.
1.2
Plumbing waste fittings are covered by ASME A1 1 2.1 8.2/CSA B1 25.2.
1.3
Other devices, e.g., temperature-actuated in-line mixing valves and flexible connectors under continuous pressure, are covered by CSA B1 25.3 or other plumbing product Standards.
1.4
This Standard does not apply to pipes and tubes or pipe and tube fittings.
1.5
In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements.
1.6 The values stated in either SI (metric) or yard/pound units are to be regarded as the standard. SI units are the units of record in Canada. In this Standard, the yard/pound units are shown in parentheses. The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard. All references to gallons are to US gallons. For information on the conversion criteria used in this Standard, see Annex A.
2 Reference publications
2.1 ASME and CSA publications
This Standard refers to the following publications, and where such reference is made, it shall be to the edition listed below, including all amendments published thereto.
ASME International (American Society of Mechanical Engineers)
A1 1 2.1 .2-1 991 (R2002)
Air Gaps in Plumbing Systems
A1 1 2.1 8.2-2005/CSA B1 25.2-05
Plumbing Waste Fittings
A1 1 2.1 8.3-2002
Performance Requirements for Backflow Devices and Systems in Plumbing Fixture Fittings
B1 .20.1 -1 983 (R2001 )
Pipe Threads, General Purpose, Inch
B1 .20.7-1 991 (R2003)
Hose Coupling Screw Threads, Inch
B1 6.1 8-2001
Cast Copper Alloy Solder Joint Pressure Fittings
B1 6.22-2001
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
B1 6.26-1 988
Cast Copper Alloy Fittings for Flared Copper Tubes
PTC 1 9.2-1 987 (R1 998)
Pressure Measurements, Instruments and Apparatus
PTC 1 9.5-1 972
Application Part II of Fluid Meters: Interim Supplement to Ptc 19.5 on Instruments and Apparatus
CSA (Canadian Standards Association)
ASME A1 1 2.1 8.2-2005/CSA B1 25.2-05
Plumbing waste fittings
CAN/CSA-B64 Series-01
Backflow preventers and vacuum breakers
B1 25.3-05
Plumbing fittings
CAN/CSA-C22.2 No. 223-M91 (R1 999)
Power supplies with extra-low-voltage Class 2 outputs
ASSE (American Society of Sanitary Engineering)
1 01 6-2005
Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations
1 01 9-1 997
Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type
ASTM International (American Society for Testing and Materials)
B 1 1 7-03
Standard Practice for Operating Salt Spray (Fog) Apparatus
B 368-97 (2003) e1
Standard Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)
B 380-97 (2002)
Standard Test Method of Corrosion Testing of Decorative Electrodeposited Coatings by the Corrodkote Procedure
B 571 -97 (2003)
Standard Practice for Qualitative Adhesion Testing of Metallic Coatings
D 968-93 (2001 )
Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
D 3359-02
Standard Test Methods for Measuring Adhesion by Tape Test
D 4060-01
Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
G 85-02e1
Standard Practice for Modified Salt Spray (Fog) Testing
ISA (Instrumentation, Systems, and Automation Society)
ANSI/ISA-75.02-1 996
Control Valve Capacity Test Procedures
MC96.1 -1 982
Temperature Measurement Thermocouples
ISO (International Organization for Standardization)
228-1 :2000
Pipe threads where pressure-tight joints are not made on the threads — Part I: Dimensions, tolerances and
designation
NSF International
NSF/ANSI 61 -2003e
Drinking Water System Components — Health Effects
SAE International (Society of Automotive Engineers)
J51 2 (April 1 997)
Automotive Tube Fittings
UL (Underwriters Laboratories Inc.)
1 31 0 (1 994)
Standard for Class 2 Power Units